!NEW!! This is our MISSOURI SUPER DUAL GENERAL WIND TURBINE 2000 watts plus potential power. Our most powerful wind turbine for home or business use.

We now offer DHL international shipping, approximately 2 to 3 business days, door to door!

Our unrivaled Generation 4 Raptor blades self regulate their speed in high winds. - No slip rings to fail or replace. Simple and effective, the turbine uses a wire tension system which will last a lifetime. The single power transmission cord never twists because the wind never spins the turbine around in the same direction hundreds of times. Typically, the wind only comes from two directions. It has yet to be an issue with any one of the thousands of turbines we have distributed.

Uses: Battery or battery bank charging, battery based and stackable wind turbine grid tie inverters, direct DC water heating elements, direct DC resistive heating, or other applications where 3 phase AC or DC can be used. (Cannot be plugged directly into a house outlet or other power source without the proper grid tie inverter)

3 phase output is the most efficient , no voltage and amperage loss in long runs like DC suffers from. DC output requires heavy expensive cable and has a high power loss over long runs. (the wind turbines shown above and below COME UNPAINTED)

Note: If you are replacing a DC output wind turbine with our 3 phase turbine and do not want to change your DC wiring then you can mount the bridge rectifier at the top of the tower for a DC run down.

The turbine comes with:

Renegade Super Dual PMA with 28 magnet rotor and dual stator. Some specifics: This is our newest PMA, the Renagade Super Dual 2,800 Watt Plus Permanent 28 Magnet Alternator: 12/24, 24/48, and 48/96 Volt models available. Please choose wind turbine voltage before checkout. Example: If you have a 24 volt battery bank choose the 24/48 volt model.

These are our highest amp models for wind turbine applications. It has our 28 N45 magnet dual rotor dual stator inside and comes with 2 rectifiers. Features a heavy duty stainless steel middle section and heavy duty bearings. Produce more power in extremely low winds or double the voltage output easily from 12 to 24v, 24 to 48v, or 48 to 96 volt. This is a very versatile permanent magnet alternator.

Turbine also includes:

Mounting Bracket and Heavy Duty 2 arms tail assembly.

Tail fin: measures 9" wide x 28" tall for maximum tracking w/ the Missouri Wind logo laser cut into the fin.

11 nylon and carbon fiber composite blades - Aerodynamically tapered Genuine RAPTOR GENERATION 4 Blades â„¢ for maximum output.

Steel blade hub is 1/4" thick x 9" in diameter

Mounting Bracket Fits on 1.5" schedule #40 or #80 pipe.

Heavy duty Hub spacer/stabilizer

Two 3 phase to DC bridge rectifiers

Specifications:

11 blade Turbine weighs 40 lbs.

Blades Make 62 1/2" dia.

125,000 hours + of rated bearing life.

RENEGADE SUPER DUAL PMA has no brushes, very dependable!

FOR EXTREME LOW WIND CONDITIONS: Blades begin to spin at ONLY 7 MPH - Wind Zone 1 - and begin making power immediately!


Below is a customer video of Dual Renegade PMA being run with three medium sized 30 inch long Falcon Mach3 blades right off the ground! Thanks Ian.






Why 9 or 11 blades?

Because the RENEGADE SUPER DUAL PMA has a high amp output. High amp output requires a lot of torque so we designed the 9 and 11 blade system to do two things...Have high torque and extreme low wind start up.

Once a gust of wind starts the blades turning, the mere weight of the hub and blades acts like a flywheel and just keeps turning as the wind speed slows.

The Missouri General Turbine has an extra large tail fin for maximum tracking in the wind and increases air flow though the blades which increases the power output.

Our 11 blade hub is 9" in dia. x 1/4" thick, the hub is supported with our hub spacer stabilizer. This keeps the hub from flexing or vibrating in high winds.

The General uses our genuine RAPTOR blades for the highest speed possible. Higher speed means greater output. All PMAs need high speed to generate any usable power, high speed cannot be accomplished by aluminum blades with a large round pitch, wooden blades, or PVC blades.

All Missouri Wind Turbines are manufactured by Missouri Wind and Solar in Seymour, Missouri USA and have the MW logo laser cut in the tail fin. Our Genuine Raptor Blades all have "RAPTOR " and USA in the base of the blade. IF it does not say RAPTOR, USA it is NOT a genuine Raptor blade made in Missouri.

Blade start up is 7 MPH winds. Once started, the wind can slow to 2 to 3 mph before the blades stop turning. The turbine comes with: blades and hub assembly, PMA, mounting bracket, tail arms, tail, and the hardware to bolt those components together and does not come with cable, charge controller, tower, or any other accessories for using or installing the wind turbine.
To obtain maximum output from our wind turbines your tower should be a minimum of 60 foot high preferably in a clearing, free from obstructions like buildings and trees. Your wind turbine should be above tree tops and buildings. Wind turbines mounted on roof tops or connected to the end of buildings will see less output due to turbulent wind "dirty wind ". RULE , the higher the better. Even though you may not be able to have a tall tower decent power is still obtainable on roof tops and short towers . The wind can blow 24 hours a day while solar is limited to 8 hours or less. One small wind turbine probably cannot equal the output of 10 solar panels. Our wind turbines do not furl which means they can keep producing power in high winds unlike turbines that are designed to shut down at 30 mph using an electrical brake or furling. Our Raptor Generation 4 â„¢ wind turbine blades are self regulating and have been tested to 125 mph winds by us. Less blades equal higher rpms ,more output but higher winds for startup. More blades equal lower wind speed startups but less output in higher winds. Our wind turbines perform the best in wind zones 2 to 7. Our wind turbines are capable of producing 500 to 2000 watts plus instantaneously in higher wind gusts. If your intending on installing your wind turbine in a low wind area or in a bad location such as roof top or behind a building it will still work for battery charging, or grid feeding etc..., however just at a lower rate and time.
The graphs in the additional images below are for a single pma. The dual begins producing about double the amperage at about 200 rpm (around 8mph wind).